dl580 gen8 manual

dl580 gen8 manual

Please try again later. Learn more at the Official Hewlett Packard Enterprise Website. - HPE ProLiant DL580 Gen8 - QuickSpecs - c04200246.pdf. Part Number: February 2014 Edition: 1 The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Microsoft, Windows, and Windows Server are U.S. registered trademarks of Microsoft Corporation. Component identification 6 The default position for all twelve positions is Off. This switch setting determines the BIOS mode the system defaults to when configuration memory is cleared to factory defaults. The User defined defaults setting in UEFI System Utilities supersedes this switch. IMPORTANT: To avoid a mismatch between boot modes, HP recommends setting system maintenance switch 7 to the same BIOS boot mode the server is deployed in. Otherwise, the storage controller may not recognize the OS installed on the storage media. NMI jumper The NMI jumper allows administrators to perform a memory dump before performing a hard reset. Crash dump analysis is an essential part of eliminating reliability problems, such as hangs or crashes in OSs, device drivers, and applications. Many crashes can freeze a system, requiring you to do a hard reset. Resetting the system erases any information that would support root cause analysis. Systems running Microsoft Windows experience a blue-screen trap when the OS crashes. When this happens, Microsoft recommends that system administrators perform an NMI event by temporarily shorting the NMI header with a jumper. The NMI event enables a hung system to become responsive again. Component identification 12. Component identification 13 Install DIMMs in pairs in alphabetical order.http://adventglobal.com/EditorImages/brute-air-compressor-manual.xml

• dl580 gen8 manual, dl580 gen8 quickspecs, dl580 gen8 user guide, dl580 gen8 quickspecs pdf, proliant dl580 gen8 manual, 1.0, dl580 gen8 manual, dl580 gen8 quickspecs, dl580 gen8 user guide, dl580 gen8 quickspecs pdf, proliant dl580 gen8 manual.

Item Description 1 Board B DIMM fault identification button 2 Board A DIMM fault identification button Component identification 18 Drive bay numbering Drives installed in bays 6-10 require the optional SAS backplane. Component identification 19 Flashing blue 2 Activity ring Rotating green Drive activity Off The drive carrier firmware is being updated or requires an update. No drive activity 3 Do not remove Solid white Do not remove the drive. Removing the drive causes one or more of the logical drives to fail. Off Removing the drive does not cause a logical drive to fail. 4 Drive status Solid green The drive is a member of one or more logical drives. Flashing green The drive is rebuilding or performing a RAID migration, strip size migration, capacity expansion, or logical drive extension, or is erasing. The drive is not configured and predicts the drive will fail. Solid amber Off The drive has failed. The drive is not configured by a RAID controller. Component identification 20 The LEDs are duplicated on the reverse side of the cache module to facilitate status viewing. 1 - Amber 2 - Green 3 - Green Interpretation Off Off Off The cache module is not powered. Off Off Flashing once every 2 seconds Flashing once per second Flashing once every 2 seconds Flashing once per second The cache microcontroller is executing from within its boot loader and receiving new flash code from the host controller. The cache module is powering up, and the capacitor pack is charging. Component identification 21 22 1 - Amber 2 - Green 3 - Green Interpretation Off Off Flashing once per second The cache module is idle, and the capacitor pack is charging. Off Off On The cache module is idle, and the capacitor pack is charged. Off On On The cache module is idle, the capacitor pack is charged, and the cache contains data that has not yet been written to the drives. Off Flashing once per second Off A backup of the DDR content on the cache module is in progress.http://www.chriton.com/upimages/userfiles/brute-briggs-and-stratton-lawn-mower-manual.xml

Off On Off The current backup is complete with no errors. Flashing once Flashing once Off The current backup failed, and data has been lost.Data may be corrupt. On Off An overtemperature condition exists. Flashing twice per second Flashing twice per second Off On The capacitor pack is not attached. The capacitor has been charging for 10 minutes, but has not reached sufficient charge to perform a full backup. On On Off The current backup is complete, but power fluctuations occurred during the backup. On On On The cache module microcontroller has failed. Power down the server WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment, remove the power cord to remove power from the server. Portions of the power supply and some internal circuitry remain active until AC power is removed. IMPORTANT: If installing a hot-plug device, it is not necessary to power down the server. 1. Back up the server data. 2. Shut down the operating system as directed by the operating system documentation. When the server activates Standby power mode, the system power LED changes to amber. IMPORTANT: Pressing the UID button illuminates the blue UID LEDs on the front and rear panels. In a rack environment, this feature facilitates locating a server when moving between the front and rear of the rack. 4. Disconnect the power cords. The system is now without power. Extend the server from the rack WARNING: To reduce the risk of personal injury or equipment damage, be sure that the rack is adequately stabilized before extending a component from the rack. WARNING: To reduce the risk of personal injury, be careful when pressing the server rail-release latches and sliding the server into the rack. The sliding rails could pinch your fingers. To extend the server from the rack: 1. Pull down the quick-release levers on each side of the server to release the server from the rack. If necessary, loosen the rack screws. Operations 23 24 2.

Extend the server on the rack rails until the server rail-release latches engage. 3. After performing the installation or maintenance procedure, slide the server into the rack by pressing the server rail-release latches. Remove the server from the rack WARNING: To reduce the risk of personal injury or equipment damage, be sure that the rack is adequately stabilized before extending a component from the rack. WARNING: To reduce the risk of personal injury, be careful when pressing the server rail-release latches and sliding the server into the rack. The sliding rails could pinch your fingers. Operations 24 25 kg lb This symbol indicates that the component exceeds the recommended weight for one individual to handle safely. WARNING: To reduce the risk of personal injury or damage to the equipment, observe local occupational health and safety requirements and guidelines for manual material handling. To remove the server from the rack: 1. Pull down the quick-release levers on each side of the server to release the server from the rack. If necessary, loosen the rack screws. 2. Extend the server on the rack rails until the server rail-release latches engage. 3. Remove the server from the rack. After performing the installation or maintenance procedure, do the following: 1. Mount the server on the rails: Operations 25 26 o Top loading telescoping rails o Front loading telescoping rails Operations 26 27 2. Slide the server into the rack by pressing the server rail-release latches. Remove the access panel WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them. CAUTION: Do not operate the server for long periods with the access panel open or removed. Operating the server in this manner results in improper airflow and improper cooling that can lead to thermal damage. To remove the component: 1. Power down the server (on page 23). 2. Extend the server from the rack (on page 23). 3.

Open the locking latch, slide the access panel to the rear of the chassis, and remove the access panel. If the locking latch is locked, use a T-15 Torx screwdriver to unlock the latch. Operations 27 28 Processor memory drawer shipping screw locations Two orange shipping screws secure the processor memory drawer in place during shipping. You must remove the screws to access the processor memory drawer. Retain the screws for future use. Remove the processor memory drawer WARNING: The processor memory drawer weighs more than 11.3 kg (25.0 lb). Use extra caution when removing and replacing the processor memory drawer. 1. Remove the processor memory drawer shipping screws, if installed. Operations 28 29 4. Firmly holding the processor memory drawer, press the release buttons and then remove the drawer from the server. Remove the processor memory drawer cover 1. Remove the processor memory drawer shipping screws, if installed. Access the Systems Insight Display To access the Systems Insight Display: 1. Press and release the panel. Operations 29 30 2. After the display fully ejects, rotate the display to the left to view the LEDs. Remove the SPI board To remove the component: 1. Power down the server (on page 23). 2. Remove all power: a. Disconnect each power cord from the power source. b. Disconnect each power cord from the server. 3. Extend the server from the rack (on page 23). 4. Remove the access panel (on page 27). 5. Remove the processor memory drawer shipping screws, if installed. Operations 30 31 6. Extend the processor memory drawer approximately cm (1-2 inches). 7. Loosen the thumbscrews on the SPI board, and then lift the SPI board to access the cables. 8. Disconnect all cables from the SPI board. Operations 31 32 Setup Optional installation services Delivered by experienced, certified engineers, HP Care Pack services help you keep your servers up and running with support packages tailored specifically for HP ProLiant systems.

HP Care Packs let you integrate both hardware and software support into a single package. A number of service level options are available to meet your needs. HP Care Pack Services offer upgraded service levels to expand your standard product warranty with easy-to-buy, easy-to-use support packages that help you make the most of your server investments. Some of the Care Pack services are: Hardware support o 6-Hour Call-to-Repair o 4-Hour 24x7 Same Day o 4-Hour Same Business Day Software support o Microsoft operating systems o Linux operating systems o HP Insight Control o VMware Integrated hardware and software support o Critical Service o Proactive 24 o Support Plus o Support Plus 24 Startup and implementation services for both hardware and software For more information on HP Care Pack Services, see the HP website ( Rack planning resources The rack resource kit ships with all HP Intelligent Series racks. For more information on the content of each resource, see the rack resource kit documentation. Optimum environment When installing the server in a rack, select a location that meets the environmental standards described in this section. Setup 32 33 Space and airflow requirements To allow for servicing and adequate airflow, observe the following space and airflow requirements when deciding where to install a rack: Leave a minimum clearance of 63.5 cm (25 in) in front of the rack. Leave a minimum clearance of 76.2 cm (30 in) behind the rack. Leave a minimum clearance of cm (48 in) from the back of the rack to the back of another rack or row of racks. HP servers draw in cool air through the front door and expel warm air through the rear door. Therefore, the front and rear rack doors must be adequately ventilated to allow ambient room air to enter the cabinet, and the rear door must be adequately ventilated to allow the warm air to escape from the cabinet. CAUTION: To prevent improper cooling and damage to the equipment, do not block the ventilation openings.

When vertical space in the rack is not filled by a server or rack component, the gaps between the components cause changes in airflow through the rack and across the servers. Cover all gaps with blanking panels to maintain proper airflow. CAUTION: Always use blanking panels to fill empty vertical spaces in the rack. This arrangement ensures proper airflow. Using a rack without blanking panels results in improper cooling that can lead to thermal damage. The 9000 and Series Racks provide proper server cooling from flow-through perforations in the front and rear doors that provide 64 percent open area for ventilation. CAUTION: When using a Compaq branded 7000 series rack, install the high airflow rack door insert (PN B21 for 42U rack, PN B21 for 22U rack) to provide proper front-to-back airflow and cooling. CAUTION: If a third-party rack is used, observe the following additional requirements to ensure adequate airflow and to prevent damage to the equipment: Front and rear doors If the 42U rack includes closing front and rear doors, you must allow 5,350 sq cm (830 sq in) of holes evenly distributed from top to bottom to permit adequate airflow (equivalent to the required 64 percent open area for ventilation). Side The clearance between the installed rack component and the side panels of the rack must be a minimum of 7 cm (2.75 in). IMPORTANT: The HP ProLiant DL580 Gen8 Server cable management arm is not supported on Compaq branded 7000 series racks. Temperature requirements To ensure continued safe and reliable equipment operation, install or position the system in a well-ventilated, climate-controlled environment. The maximum recommended ambient operating temperature (TMRA) for most server products is 35 C (95 F). The temperature in the room where the rack is located must not exceed 35 C (95 F).

Setup 33 34 CAUTION: To reduce the risk of damage to the equipment when installing third-party options: Do not permit optional equipment to impede airflow around the server or to increase the internal rack temperature beyond the maximum allowable limits. Do not exceed the manufacturer s TMRA. Power requirements Installation of this equipment must comply with local and regional electrical regulations governing the installation of information technology equipment by licensed electricians. For electrical power ratings on options, refer to the product rating label or the user documentation supplied with that option. WARNING: To reduce the risk of personal injury, fire, or damage to the equipment, do not overload the AC supply branch circuit that provides power to the rack. Consult the electrical authority having jurisdiction over wiring and installation requirements of your facility. CAUTION: Protect the server from power fluctuations and temporary interruptions with a regulating uninterruptible power supply. This device protects the hardware from damage caused by power surges and voltage spikes and keeps the system in operation during a power failure. When installing more than one server, you may need to use additional power distribution devices to safely provide power to all devices. Observe the following guidelines: Balance the server power load between available AC supply branch circuits. Do not allow the overall system AC current load to exceed 80% of the branch circuit AC current rating. Do not use common power outlet strips for this equipment. Provide a separate electrical circuit for the server. Electrical grounding requirements The server must be grounded properly for proper operation and safety. In the United States, you must install the equipment in accordance with NFPA 70, 1999 Edition (National Electric Code), Article 250, as well as any local and regional building codes.

In Canada, you must install the equipment in accordance with Canadian Standards Association, CSA C22.1, Canadian Electrical Code. In all other countries, you must install the equipment in accordance with any regional or national electrical wiring codes, such as the International Electrotechnical Commission (IEC) Code 364, parts 1 through 7. Furthermore, you must be sure that all power distribution devices used in the installation, such as branch wiring and receptacles, are listed or certified grounding-type devices. Because of the high ground-leakage currents associated with multiple servers connected to the same power source, HP recommends the use of a PDU that is either permanently wired to the building s branch circuit or includes a nondetachable cord that is wired to an industrial-style plug. NEMA locking-style plugs or those complying with IEC are considered suitable for this purpose. Using common power outlet strips for the server is not recommended. Rack warnings Setup 34 35 WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that: The leveling jacks are extended to the floor. The full weight of the rack rests on the leveling jacks. The stabilizing feet are attached to the rack if it is a single-rack installation. The racks are coupled together in multiple-rack installations. Only one component is extended at a time. A rack may become unstable if more than one component is extended for any reason. WARNING: To reduce the risk of personal injury or equipment damage when unloading a rack: At least two people are needed to safely unload the rack from the pallet. An empty 42U rack can weigh as much as 115 kg (253 lb), can stand more than 2.1 m (7 ft) tall, and might become unstable when being moved on its casters. Never stand in front of the rack when it is rolling down the ramp from the pallet. Always handle the rack from both sides.

Identifying the contents of the server shipping carton Unpack the server shipping carton and locate the materials and documentation necessary for installing the server. All the rack mounting hardware necessary for installing the server into the rack is included with the rack or the server. The contents of the server shipping carton include: Server Power cord Hardware documentation, Documentation CD, and software products Rack-mounting hardware In addition to the supplied items, you might need: Operating system or application software Hardware options Installing hardware options Install any hardware options before initializing the server. For options installation information, refer to the option documentation. Install the heaviest item first, and continue to populate the rack from the bottom to the top. 1. Install the server and cable management arm into the rack. For more information, see the installation instructions that ship with the Quick Deploy Rail System. 2. Connect peripheral devices to the server.Part Number: 666296-001 March 2012 Edition: 1 Copyright This guide is for technicians that install, administer, Class B devices have a Federal Communications Installation Instructions May 2005 (Second Edition) Part Number 346896-002 This document is for the This guide describes identification Choosing a Setup Location. General Server Precautions. Barracuda Appliances The Rack Mounting Instructions section below provides information on installing the SC825 chassis into a rack unit Upgrading and Servicing Guide Hewlett-Packard Company makes no warranty of any kind with regard to Following these steps in the order given For the latest Part Number: 653239-005 June 2014 Edition: 5 Copyright Dual-Bay RAID Storage Enclosure for two 3.5-inch Serial ATA Hard Drives. User Manual March 31, 2014 v1.2 www.akitio. Microsoft, Windows, and Windows Nothing herein should be construed If you no longer User Guide Nothing herein should All Rights Reserved.

No part of this manual, including the products and software described in it, may Installation Manual American Megatrends, Inc. 5555 Oakbrook Parkway, Building 200 The Blade Server features one or two Intel Pentium 4 Xeon processors, the Intel The family of allows multiple servers in a rack to be This guide provides procedures for installing the kit components, User Guide HP Part Number: 616896-002 Published: August 2011 Edition: 1 Copyright User Guide HP StorageWorks Modular Smart Array 50 Enclosure. Overview This enclosure delivers industry-leading data performance, Before you install the server in a rack cabinet, review the following guidelines: April 2004 (First Edition) Part Number 354903-001 The only warranties for HP products and services Models HP 30-Notebook Charging Cart. HP 30-Notebook Managed Charging Cart A01 Copyright 2010 Dell, Inc. All rights reserved. Dell is a trademark of Dell, Inc. EqualLogic is a registered trademark. All trademarks Microsoft and Windows are U.S. registered User Guide Windows and Windows Connections for two local consoles (a console represents one keyboard, monitor and mouse) allow access Some features may not be available on your computer. Microsoft and Windows are U.S. registered trademarks To use this website, you must agree to our Privacy Policy, including cookie policy. Part Number: 742029 - 001 Febru ary 2014 Edition: 1 1 2 3. 109 Summary of content (109 pages) Page 1 HP ProLiant DL580 Gen8 Server User Guide Abstract This document is for the person who installs, administers, and troubleshoots servers and storage systems. HP assumes you are qualified in the servicing of computer equipment and trained in recognizing hazards in products with hazardous energy levels. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.

HP shall not be liable for technical or editorial errors or omissions contained herein. Page 4 Powering on and selecting a boot option. 38 Registering the server. 38 Hardware options installation. 39 Introduction. Page 5 HP Smart Storage Administrator. 80 Option ROM Configuration for Arrays. 81 ROMPaq utility. 81 Automatic Server Recovery. The default position for all twelve positions is Off. Install DIMMs in pairs in alphabetical order. Page 16 Processors and memory cartridges The processor memory drawer contains 4 processor sockets and 8 memory cartridges. Page 19 Memory error LEDs When the DIMM fault LEDs (on page 17) indicate that a DIMM is experiencing an error, the memory error LED below the affected DIMM illuminates red when the DIMM fault identification button (on page 18) is pressed. Drive bay numbering Drives installed in bays 6-10 require the optional SAS backplane. Page 20 Hot-plug drive LED definitions Item LED Status Definition 1 Locate Solid blue The drive is being identified by a host application. Flashing blue The drive carrier firmware is being updated or requires an update. Rotating green Drive activity Off No drive activity Solid white Do not remove the drive. Removing the drive causes one or more of the logical drives to fail. Off Removing the drive does not cause a logical drive to fail. Page 21 FBWC capacitor slots Item Description 1 Slots 2-4—Connect to optional SAS controllers 2 Slot 1—Connects to the SPI board FBWC module LEDs The FBWC module has three single-color LEDs (one amber and two green). The LEDs are duplicated on the reverse side of the cache module to facilitate status viewing. 1 - Amber 2 - Green 3 - Green Interpretation Off Off Off The cache module is not powered. Page 22 1 - Amber 2 - Green 3 - Green Interpretation Off Off Flashing once per second The cache module is idle, and the capacitor pack is charging. Off Off On The cache module is idle, and the capacitor pack is charged.

Off On On The cache module is idle, the capacitor pack is charged, and the cache contains data that has not yet been written to the drives. Off Flashing once per second Off A backup of the DDR content on the cache module is in progress. Power down the server WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment, remove the power cord to remove power from the server. Portions of the power supply and some internal circuitry remain active until AC power is removed. Page 24 2. Extend the server on the rack rails until the server rail-release latches engage. 3. After performing the installation or maintenance procedure, slide the server into the rack by pressing the server rail-release latches. Remove the server from the rack WARNING: To reduce the risk of personal injury or equipment damage, be sure that the rack is adequately stabilized before extending a component from the rack. Page 25 This symbol indicates that the component exceeds the recommended weight for one individual to handle safely. 32.18-52.87 kg WARNING: To reduce the risk of personal injury or damage to the equipment, observe 70.94-116.56 lb local occupational health and safety requirements and guidelines for manual material handling. To remove the server from the rack: 1. Pull down the quick-release levers on each side of the server to release the server from the rack. If necessary, loosen the rack screws. 2. Page 26 o Top loading telescoping rails o Front loading telescoping rails Operations 26 Page 27 2. Slide the server into the rack by pressing the server rail-release latches. Remove the access panel WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them. CAUTION: Do not operate the server for long periods with the access panel open or removed. Operating the server in this manner results in improper airflow and improper cooling that can lead to thermal damage.

To remove the component: 1. Page 28 Processor memory drawer shipping screw locations Two orange shipping screws secure the processor memory drawer in place during shipping. You must remove the screws to access the processor memory drawer. Retain the screws for future use. Remove the processor memory drawer WARNING: The processor memory drawer weighs more than 11.3 kg (25.0 lb). Use extra caution when removing and replacing the processor memory drawer. 1. Remove the processor memory drawer shipping screws, if installed. Page 29 4. Firmly holding the processor memory drawer, press the release buttons and then remove the drawer from the server. Remove the processor memory drawer cover 1. Remove the processor memory drawer shipping screws, if installed. Access the Systems Insight Display To access the Systems Insight Display: 1. Page 30 2. After the display fully ejects, rotate the display to the left to view the LEDs. Page 32 Setup Optional installation services Delivered by experienced, certified engineers, HP Care Pack services help you keep your servers up and running with support packages tailored specifically for HP ProLiant systems. HP Care Packs let you integrate both hardware and software support into a single package. A number of service level options are available to meet your needs. Power requirements Installation of this equipment must comply with local and regional electrical regulations governing the installation of information technology equipment by licensed electricians. The full weight of the rack rests on the leveling jacks. The stabilizing feet are attached to the rack if it is a single-rack installation. The racks are coupled together in multiple-rack installations. Only one component is extended at a time. A rack may become unstable if more than one component is extended for any reason.

Page 36 WARNING: To reduce the risk of electric shock, fire, or damage to the equipment, do not plug telephone or telecommunications connectors into RJ-45 connectors. 3. Connect the power cord to the rear of the server. 4. Install the power cord anchors. 5. Secure the cables to the cable management arm. IMPORTANT: When using cable management arm components, be sure to leave enough slack in each of the cables to prevent damage to the cables when the server is extended from the rack. Page 37 6. Connect the power cord to the AC power source. Intelligent Provisioning can configure the server and install an operating system, eliminates the need for SmartStart CDs and Smart Update Firmware DVDs used in past generations of HP ProLiant servers. To install an operating system on the server with Intelligent Provisioning (local or remote): a. Page 39 Hardware options installation Introduction If more than one option is being installed, read the installation instructions for all the hardware options and identify similar steps to streamline the installation process. WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them. CAUTION: To prevent damage to electrical components, properly ground the server before beginning any installation procedure. Page 40 Installing the processor The processors and memory are located in the drawer accessible from the front of the server. It is not necessary to extend or remove the server from the rack to install or replace processors and memory. WARNING: Use caution when installing or removing the processor memory drawer. The processor memory drawer is very heavy when fully populated. Page 41 7. Open each of the processor locking levers in the order indicated, and then open the processor retaining bracket. 8. Remove the clear processor socket cover. Retain the processor socket cover for future use. Page 42 9. Install the processor.